Guided workflow
Calculate Stress-Strain Properties
Calculate common tensile stress–strain properties from data that is already expressed as stress versus strain. NotyPlot normalizes supported stress/strain units and can estimate Young’s modulus, offset yield strength, ultimate tensile strength and fracture/elongation values for review.
- NotyPlot
- MECHANICAL
- 6 steps
Start with Mechanical test data with correctly defined stress and strain.
- Import the mechanical data
- Check units and conversions
- Review the elastic-region fit
- Inspect mechanical properties
- Refine the elastic interval
- Export and document conditions
Result Reviewed mechanical-property calculations and a stress-strain plot.
Figure 1. The workflow at a glance: what you start with, the steps, and what you leave with.
Before you start
- A monotonic engineering stress–strain dataset or clearly defined equivalent columns.
- Known strain units (fraction or percent) and stress units (Pa, kPa, MPa or GPa).
- Stress rather than raw load, and strain rather than raw extension; geometry is needed upstream if conversion has not already been done.
Your workflow
Step-by-step workflow
Import the mechanical data
Import the mechanical dataset and map the strain and stress columns.
Check units and conversions
Confirm units and verify that raw extension or force has already been converted when necessary.
Review the elastic-region fit
Run mechanical analysis and inspect the automatically selected elastic region and its linear-fit quality.
Inspect mechanical properties
Review Young’s modulus, the configured offset yield strength, UTS, fracture stress and elongation/fracture strain.
Refine the elastic interval
Override the elastic-region endpoint only when the measured curve supports a better defensible interval.
Export and document conditions
Export the reviewed properties and curve together with specimen geometry, test standard and conditions from the experiment record.
Final quality check
- The X-axis is strain and the Y-axis is stress, not displacement and load.
- The elastic-region fit is physically plausible and sufficiently linear.
- The offset-yield construction intersects the measured curve appropriately.
- Fracture and UTS values correspond to the intended tensile-test interpretation.
- Report engineering versus true stress/strain explicitly.
- Keep specimen dimensions and test standard outside the plot result when they are needed to reproduce stress or strain conversion.
- Compare samples only under compatible loading and specimen conditions.
Scientific notes
- The workflow cannot derive stress from force without specimen cross-sectional area, or strain from extension without gauge length.
- Automatic elastic-region detection may be unreliable for toe regions, nonlinear materials or noisy data.
- Mechanical properties depend on specimen geometry, test method, strain rate and data processing, not only the plotted curve.
Common questions
Can I import load–extension data directly?
Not for final mechanical-property calculation unless it has been converted to stress and strain using the specimen geometry.
How is yield strength estimated?
The service uses an offset-yield construction with a configurable engineering-strain offset, commonly 0.2%, after fitting the elastic region.
Why is Young’s modulus wrong even though the curve looks correct?
Check strain scaling, stress units and the selected elastic interval. Percent-versus-fraction strain is a common source of large errors.
Related resources
- Workflow Analyze TGA Mass Loss and DTG Analyze thermogravimetric mass-loss steps together with the derivative thermogravimetry (DTG) curve. NotyPlot uses the derivative to help resolve loss events and reports step ranges, DTG peak temperatures and residual mass for review.
- Workflow Automatic XRD Peak Analysis in NotyPlot Run a guided automatic XRD peak-analysis pass, then review the detected and fitted results rather than treating automation as a final interpretation. The workflow is designed to shorten setup while keeping peak selection, fitting and scientific checks visible.
- Workflow Calculate Crystallite Size and Microstrain with Williamson-Hall Separate size-related and strain-related contributions to XRD peak broadening with a Williamson–Hall analysis built from several reviewed fitted peaks. The workflow emphasizes peak eligibility and the transformed linear fit because a numerical intercept and slope are only useful when the selected peaks support the model.
- Workflow Calculate Crystallite Size from XRD Using the Scherrer Equation Estimate coherent crystallite size from suitable fitted XRD peak widths using the Scherrer equation. The workflow keeps wavelength, shape factor, fitted FWHM and instrumental broadening visible because each directly affects the reported size.
Start this workflow
Prepare your input and follow the guided steps in NotyPlot.
